EP brand name alternative gearbox for woods rotary gearbox
NEW forty HP GEARBOX Smooth Enter one 3/8 12 spline output Interchangable with industry popular dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous Far more
Attributes
(1) model new 45 horse energy shearpin gearbox. This gearbox fits many various can make of 4′,5′ and some 6′ rotary cutters. I offer a good deal of these containers each and every 12 months for a number of distinct purposes and have ALL Substitute Parts for this box, but hopefully you is not going to have to fear about that.
Here are the specs on the box:
*forty five horse power gearbox
*Normal 1-three/eight” clean input shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a one/two shearbolt.
*length of the enter shaft out of the gearbox is three” long
*bolt hole pattern for mounting is on the corners, four-three/four center of hole to heart of hole. It normally takes a 5/eight” bolt.
*twelve splined output shaft(exactly where the blade carrier hooks up on the bottom)
*one-nine/sixteen exterior measurement in excess of the output shaft splines- from the foundation of the output cap to the finish of the splines is two-3/four” lengthy- all round duration of the output shaft is four-one/2″ extended.
*requires a one” threaded castle nut and a carter essential on the base of the output shaft to secure blade pan(NUT is provided – – BLADE PAN IS NOT!!)
*all round top of the box from the top of the mower deck to the prime of the box is nine-one/2″
This is a reasonably hefty merchandise (forty seven lbs.) so freight is not inexpensive, but we do not make everything off of freight, what ever ups expenses us we charge you.
forty HP
one:one:47 Ratio
one-3/eight” Easy Input Shaft with Shear Pin Hole
one-one/two” 12-Spline Ouput Shaft 
Bolt Pattern: six-one/two” (4) 5/eight” Holes, 5″ Heart Hole Required for Shaft Assembly
The Enter and Output Shafts Cannot be Purchased Serparately.
They are Sold as a kit.
The package contains the pursuing components: enter shaft, enter equipment, output shaft, output gear.
The Shaft Kit Are not able to Be Separated.
EP model alternative gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Manual
Is your mower leaking, creaking or normally doing incorrectly? You’ve got come to the correct location.
Read through below for the most widespread concerns with rotary cutter gearboxes and their solutions (from rapid and soiled, to professional).
Leaking Base Seal:
If you’ve wrapped some baling or fencing wire all around your output shaft and blown the seal, the specialist factor to do is to exchange the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing residences can purchase you up a generic double-lip seal that will get you back up-and-working. If not, give us a call and we can aid you kind out what you require.
A dental select is the least difficult way to remove the outdated seal prior to urgent in the new one.
If you might be fortunate adequate to have a slow-leak, the rapid and soiled strategy is to operate automotive-type grease in the gearbox till the new seal arrives in. Be certain to verify and insert grease more frequently than you would with oil, as this is NOT a specialist repair.
Damaged Output Shaft:
Uh oh. You hit some thing that did not transfer. The excellent news is that the output shaft on most gearboxes is reasonably straightforward to replace. The poor information is… it’s seldom an isolated failure.
The very first point to do is to take apart your gearbox and evaluate the entire extent of the harm. If it is genuinely just the output shaft, you need to be in a position to adjust it out, no issue. The output shafts start off at about $70 and go up in price dependent on the size of the gearbox.
Nevertheless, in most instances, the bearings ($twenty/ea), seals ($10/ea) and equipment-set ($70) will also typically just take a beating. If you happen to be unfortunate, the output cap ($80) will also undergo some injury.
In this scenario, it is normally less expensive to replace the gearbox. Assess the price tag of components to the expense of an total, new, warrantied gearbox. Sometimes, even pros have to know when to get in touch with it a day.
I Want to Alter my Input Shaft:
If you are fatigued of changing shear pins or searching back again and looking at that your mower hasn’t been reducing, you could want to set up a slip-clutch pto shaft (Sure, we promote people as well).
This normally calls for putting in a 540-fashion, six-spline enter shaft ($85) on your mower’s gearbox.
Fortunate for you, we did a publish-up on our website. It is called “How to alter the enter shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem kind-of equivalent over-the-cellphone. The best point to do is to disassemble your gearbox and get a search at the gears and bearings. The problem will generally existing by itself in the way of broken/lacking equipment teeth, toasted gears (like that photo on our home webpage), or blown bearings.
If every little thing seems to be normal, try altering the gear-mesh. This is accomplished with the mylar “gaskets” that sit between the major gearbox circumstance and the input/output caps. Attempt adding or taking away some of these spacers until finally your gears have about one/eight”-one/4″ of free of charge play. Specialists can purchase replacements ($one-two) in different thicknesses, but we advise the quick and filthy technique of chopping your possess out of a sheet of mylar.
Never forget to re-seal the gearbox with RTV soon after you’ve got located the correct mix. Even however they are known as “gaskets”, they is not going to seal your gearbox on their personal.
Gearbox geared motors For Horticulture Drive Systems plays a substantial component in daily life, see our website https://www.ssj-group.com/agricultural-gearbox/ to see just how.