The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product collection of the complete gearbox and gear-electric motor system. Cat4CAD supports you in choosing and configuring these products, provides you the opportunity to print out extensive technical data linens, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sizes.
Multiple Input Options: Integral gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, installation pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements plus modular design to accept brakes, encoders or forced cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge surface shafts
Shaft mounting options include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It is offered as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing designs include helical bevel gear reducer footed, encounter and flanged configurations. Gearmotors can be found in three phase high efficiency designs through 50 HP and single phase to 5 HP. We offer a variety of input and output shaft options. Additionally, you will find fixed and variable velocity motors and range of ratios obtainable in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Crucial dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying demands of customers, we offer a wide range of Helical Bevel Gear Reducers. The technological content of our products permits an extraordinary overall performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully found in a multitude of industrial and civil applications. These are B-Series units that offer excellent affordability and result torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with small motor, PB-fitted for electric motor coupling with flexible joint
Casing with feet FC, flange SC and general UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to ensure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel equipment motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five stages. Motors can be found up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and may be offered with single or dual extended output shafts.
Devices are also available because shaft mounted or with output flanges and are designed for mounting horizontally or vertically. The systems can also be offered with a bolt on torque reaction bracket and all variants are available either motorised or with an input shaft assembly.
Adding to the new selection of Ever-Power helical gear motors this product takes advantage of our a long time of accumulated design experience together with the usage of high quality materials and elements. The end result is a number of velocity reducing geared motors offering high load holding capacities, increased efficiency, tranquil running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double oil seals, on input and output shaft since required.
All units are dimensionally interchangeable with additional major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be installed with a backstop module and reducer Devices can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemical substances, pharma, packaging, food processing, plastic-type material and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for engine coupling, IEP – with input shaft, CEP – with small motor
Cases with feet, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and composed of Y series engine, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, helical bevel gear motor33174973057wonderful appearance ,and solid capacity of being overloaded.
6: Precise division and wide range for transmission ratio.
7: The performance is up to because high as 96% with low energy intake, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.