The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need. For use with 5/8” shaft sizes. Comes with set screws. Extra Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock metal Split Taper bushings Split Taper Bushing china feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering on hand requirements and allowing for changes in shaft size if important. The barrel of the split tapered bushing is split in two spots and can be keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, whether or not the fasteners become loose. Split tapered bushings are interchangeable between manufacturers.

Taper bushing are widely used together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are created from high quality engineered resources with wonderful tolerance. The characteristic is easy to apply and needs no additional alteration. These bushings can go well with almost a myriad of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations add bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full range of both metric and imperial obtainable.
Standard range meets up to 125mm/5″ shafts & Hub diameter required depends upon the application.
Complete short reach range offered, for compact light assemblies & Clean, Compact Design.
Ease of installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for durability and strength. U1 bushings are being used in an extensively wide selection of applications, which include; sprockets, shaves, pulleys, gears, plus much more, we also offer most of these products. What pieces this bushing apart is the high-quality steel development along with specific manufacturing and high quality control; this ensures that you always get a premium quality regular product. What really models us in addition to the other fellas is our experienced expert workers and our company-wide objective of customer satisfaction.
1. Be certain the tapered cone surfaces of the bushing and the within of the driven product will be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or different component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding fit on shaft.
4. With major on shaft, slide the sprocket or other portion type to the required position on the shaft. Make sure you keep the heads of the cap screws attainable.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they happen to be pulled up tight. Usually do not make use of extensions on the wrench handles , nor allow the sprocket or component to end up being drawn i contact with flange of bushing. At this stage there should be a gap between your bushing flange and sprocket, make sure this gap will not close.
Twice split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for great drive and increased torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep up concentric bores
Available in in ., metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys upon both the shaft and item to supply the strongest possible travel.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest amount of mechanical locking product to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as split taper bushing201909201716412902737the pulley you need. For apply with 5/8” shaft sizes. Includes set screws. More Features: Made of Steel For work with with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering readily available requirements and allowing for improvements in shaft size if important. The barrel of the split tapered bushing is usually split in two spots and is normally keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing could it be will hold, whether or not the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.